Follow MaxBotix:
Ask A Question

Cool Raspberry Pi Projects - Interfacing a Raspberry Pi with an ultrasonic sensor to read serial data

|     Written By: Cody Carlson    |    Date Updated: 10-18-2016     |

Back to Raspberry Pi Projects

Do you enjoy or love testing new Raspberry Pi Projects? Maxbotix has put together a tutorial that teaches you how to interface a Raspberry Pi with an ultrasonic sensor to read TTL serial data. You may also want to check out our tutorials on Using an ultrasonic sensor with a Raspberry Pi and how to use USB sensors for a Raspberry Pi.

Getting Started

The Raspberry Pi needs to install an operating system the first time it is used. This article was created for the Raspberry Pi 3 using the Raspbian Jessie operating system (downloaded on 10/06/16). This article was also successfully tested on the Raspberry Pi 2 with the same operating system. This article will be periodically updated as the operating systems, files, and settings are updated and moved.

Check out these 5 Ways New Raspbian Jessie Makes Raspberry Pi Even Easier to Use. We hope you enjoy this tutorial, after you’re done reading don’t forget to come back for more Raspberry Pi Projects exclusively provided by MaxBotix.

Key Takeaways

Raspberry Pi 2 drawing
TIP For the safety of the electronics on the Raspberry Pi and MaxBotix ultrasonic sensors, please use an ESD strap when working around components. Static discharge could damage components of the Raspberry Pi as well as the ultrasonic sensors.

Required Equipment

Directly Compatible Ultrasonic Sensors

Ultrasonic Sensors that Require an Inverter

The ultrasonic Sensors listed below provide TTL serial data and directly interface with the Raspberry Pi. The ultrasonic Sensors listed below require an inverter to operate with the Raspberry Pi.
Important: Connect the center square with the outer portion of the pad with a small amount of solder to enable the TTL output on the MB1003 Ultrasonic Sensors from the HRLV-MaxSonar-EZ line.
Ultrasonic Sensor - Solder before
Before
Ultrasonic Sensor - Solder after
After


Enable Serial Data on ttyAMA0

We want to enable the RX pin on ttyAMA0 to receive asynchronous serial data. To allow this we need to change the set the enable UART setting in the configurations files.

Open the file /boot/config.txt by using the following command:

sudo nano /boot/config.txt

Scroll to the end of the file and add the following lines to the file. Scroll to the end of the file and add the following lines to the file.

enable_uart=1
dtoverlay=pi3-disable-bt
dtoverlay=pi3-miniuart-bt
This will disable bluetooth on the Raspberry Pi 3 and allow serial communication in its place. While this isn’t fully needed for other versions of the Raspberry Pi, it will not impact their performance.

Save and close the file by simultaneously pressing Ctrl and X to exit the screen and then pressing Y to save it.

Optional: Download a Python Script

This is optional, but you may wish to write or download a Python Script to log and store the data you collect with your ultrasonic sensor.

Here is sample python code provided by one of our users to automate the reading of distance values.

Supplying Power to the Sensor

When using an XL-MaxSonar or WR ultrasonic sensor with a Raspberry Pi, it is highly recommended to use an external power supply. The Raspberry Pi is not intended to supply a high enough current draw to power these ultrasonic sensors.

Ultrasonic sensors from the LV-MaxSonar, LV-ProxSonar, HRLV-MaxSonar, and ParkSonar lines can be directly powered by the Raspberry Pi.

TIP You may want to place a capacitor between the power and ground lines immediately before the ultrasonic sensors's pinout. During the ultrasonic sensors transmit, the sensor draws a higher current for a fraction of a second. The higher current draw may cause the Raspberry Pi's microcontroller to begin to shut down. To prevent any issue with long term use, we recommend that you use a capacitor with at least a one microfarad rating to ease the current draw from the Raspberry Pi.

Wiring Instructions

Connect the female end of a jumper to pin 10 of the Raspberry Pi GPIO. This is the RX pin for serial data.

Connect a Mini-Grabber or solder a wire into pin 5 of the sensor, and connect this to the jumper.

Connect your sensor to an appropriate power supply.

Installing Terminal Software

The recommended software for accessing the range data output is Minicom. Please use the following steps to install Minicom.

Open LXTerminal
Download Minicom with the following command

sudo apt‑get install minicom
This will install the Minicom software that is used for reading the serial port.

Accessing Ultrasonic Sensor Range Data Output

Minicom is the recommended terminal software for Raspbian Jessie operating system. Please use the steps below to access Minicom and read the range data.

Open LXTerminal
Open Minicom with the following command

(For Raspberry Pi 3)

minicom -b 9600 -o -D /dev/ttyS0


(For Raspberry Pi 2)
Click Here to learn how to use USB ultrasonic sensors for a Raspberry Pi.
minicom -b 9600 -o -D /dev/ttyAMA0

This clears the LXTerminal window and you will see a window that looks similar to the image below.

Raspberry Pi Pins


The number following the ASCII character is the range reading that is output by the ultrasonic sensor. If the readout says R0764, like the image above, the range to the target is 764mm. As the target gets further away from the ultrasonic Sensor , the reported range will increase. If no target is detectable, the target will report maximum range.

Monitoring oil tank level with a MaxBotix ultrasonic sensor

Final Notes & Outcome

Using an ultrasonic Sensor with a Raspberry Pi allows for inexpensive monitoring of tank levels, height measurement, as well as countless other applications that require distance measurement. If you have any applications or code that can be added to this article, or if you would like to share pictures of your setup with us so we can share with others please email webmaster@maxbotix.com.

NOTE: This article was created for the Raspberry Pi 3 using the Raspbian Jessie operating system (downloaded on 7/18/2016).

This article was not written for Raspberry Pi 2.





 
Author: Kathy Kostal  Date: 08-31-2016
Inc 5000 Maxbotix Logo Inc. Magazine Unveils 35th Annual List of America's Fastest Growing Private Companies–the Inc. 5000. MaxBotix Inc., Ranks No. 1752 on the 2016 Inc. 5000 with Three–Year Sales Growth of 213%.
Click here for full article.
Author: Cody Carlson  Date: 08-02-2016
Raspberry Pi 2 board MaxSonar sensors offer a variety of outputs including TTL serial data. This tutorial guides you through the process of setting up your Raspberry Pi 3 with a MaxBotix sensor. Click here for full article.
Author: Scott Wielenberg  Date: 07-26-2016
Full Horn Housing MaxBotix offers an expanded range of packaging options for many of our sensors. Each option provides unique benefits to certain mounting integrations. This article provides a brief overview of each option.
Click here for full article.
Author: Scott Wielenberg  Date: 07-18-2016
Sensor is Tested When providing support, our technical support team may determine that further testing at our facility is the best way to help resolve the issue that you are facing. At this point, they will start the Return Merchandise Authorization (RMA) process. This article will explain what you can expect as your ultrasonic sensor travels through our RMA process.
Click here for full article.
Author: Scott Wielenberg  Date: 07-11-2016
Typical Wall Pipe Many customers have requested the option to mount an ultrasonic sensor in a pipe. During the testing and development cycle, we discovered a number of considerations and requirements that must be met for the application to be successful. When all of these are met, a user may be able to achieve the desired level of success for measuring the liquid level inside of a pipe.
Click here for full article.
Author: Jenney Grover  Date: 06-28-2016
one of the options for outputs On April 19th, we welcomed our supporters to join us for the Grand Opening of the Build Out. Bob and Nita Gross gave a tour of the build out and their vision for the space. We continue to be in awe of the support from our community, our employees, our distributors, and our customers. Thank you for the many years of support, and we look forward to serving you in the years to come.
Click here for full article.
 
 
 
 
 
Signup for notification of our exciting new products and periodic new letters. We are excited to provide the latest information from MaxBotix Inc.